Roofing

LIBERTY™ Self-Adhering Roofing Systems are applied without torches, open flames, hot asphalt, or solvent-based adhesives and are suitable for many primed substrates. LIBERTY™ SBS Self-Adhering Base/Ply Sheet is a self-adhering modified bitumen roofing membrane intended to be used as either a base sheet for LIBERTY™ SBS Self-Adhering Cap Sheet or as a ply sheet in modified bitumen roofing systems, providing long-lasting protection on low-slope roofs.

Synthetic Underlayments

SYNTHETIC GUARD™ PLUS UNDERLAYMENT
A non-woven synthetic underlayment with a grey coated polypropylene spun-bond fabric surface, a polypropylene 10 × 5 scrim and a grey backside coating.

SYNTHETIC GUARD™ UNDERLAYMENT
A non-woven synthetic underlayment with a black coated polypropylene spun-bond fabric surface, a polypropylene 5 × 5 scrim, and a black backside coating.

No. 15 Underlayments

NO. 15
Features a TAMKO organic felt saturated with asphalt. Accepted for use as an underlayment felt to be applied over the deck prior to the installation of TAMKO asphalt shingles.

NO. 15 ASTM
Features a TAMKO organic felt saturated with asphalt. Accepted for use as an underlayment felt to be applied over the deck prior to the installation of TAMKO asphalt shingles.

NO. 15 ASTM D4869
Features a TAMKO organic felt saturated with asphalt. Accepted for use as an underlayment felt to be applied over the deck prior to the installation of TAMKO asphalt shingles.

NO. 15 UL
Features a TAMKO organic felt that is saturated with asphalt. Accepted for use as an underlayment felt to be applied over the deck prior to the installation of TAMKO asphalt shingles.

Other Underlayments

TAM-FELT®
A TAMKO organic (non-perforated) felt that is saturated with asphalt. TAM-FELT® serves as an alternative to ASTM D226 Type I & II saturated felt, and has been tested by a third-party laboratory in accordance with ICC-ES AC188 and the physical properties of ASTM D226.

ASTM TILE UNDERLAYMENT
Accepted for use as an underlayment felt to be applied over the deck prior to the installation of concrete tile. This underlayment contains a TAMKO organic felt saturated with asphalt, then coated on both sides with a weathering-grade asphalt and surfaced with opaque granules.

No. 30 Underlayments

NO. 30
A non-UL saturated felt made with a TAMKO organic felt (non-perforated) saturated with asphalt. Accepted for use as an underlayment felt to be applied over the deck prior to the installation of TAMKO asphalt shingles.

NO. 30 18-INCH
Features a TAMKO organic felt that is saturated with asphalt. Accepted for use as an underlayment felt to be applied over the deck prior to the installation of wood shake shingles.

NO. 30 ASTM
Features a TAMKO organic felt that is saturated with asphalt. Accepted for use as an underlayment felt to be applied over the deck prior to the installation of TAMKO asphalt shingles.

NO. 30 ASTM D4869
Features a TAMKO organic felt that is saturated with asphalt. Accepted for use as an underlayment felt to be applied over the deck prior to the installation of TAMKO asphalt shingles.

NO. 30 UL
Features a TAMKO organic felt (non-perforated) that is saturated with asphalt. Accepted for use as an underlayment felt to be applied over the deck prior to the installation of TAMKO asphalt shingles.

NO. 30 ASTM SHAKE UNDERLAYMENT
Features a TAMKO organic felt (non-perforated) that is saturated with asphalt. Accepted for use as an underlayment felt to be applied over the deck prior to the installation of TAMKO asphalt shingles.

SHAKE UNDERLAYMENT
Features an organic felt (non-perforated) that is saturated with asphalt. Accepted for use as an underlayment felt to be applied over the deck prior to the installation of wood shake shingles.

Self-Adhering Underlayments

MOISTURE GUARD®
For use as a self-adhering underlayment prior to installation of the final roof system and as a secondary layer in areas susceptible to windblown rain and ice damming. Moisture Guard is used on roof decks, around chimneys, dormers, vents and skylights, and along rake and eave edges, valleys and ridges. Moisture Guard is used under most types of roofing, including tile, wood shake, asphalt, slate or composite shingles. It is not recommended for use under metal roofing.*

TW UNDERLAYMENT
A self-adhering rubberized asphalt sheet membrane with a polymer film on the surface and a removable treated release film on the adhesive side. Surface is textured for skid resistance and can be left exposed for up to 120 days.

TW METAL AND TILE UNDERLAYMENT
A fiberglass-reinforced self-adhering rubberized asphalt sheet membrane with a polymer film on the surface. Features a removable treated release film on the adhesive side for convenient installation and handling. TW Metal & Tile Underlayment can be left exposed for up to 120 days and is used under metal roofs, mechanically fastened tile, slate, wood shakes, asphalt and composite shingles.

TW SEAM TAPE
A flexible, self-adhering SBS modified bitumen roof deck seam tape with a polymer film on the surface and a removable treated release film on the adhesive side. For use as a roof deck seam tape to cover all joints and seams. Provides secondary protection against water penetration at deck seams and joints.

Starter/Hip & Ridge

Starter Shingles

HERITAGE® VINTAGE® SHINGLE STARTER
Part of a two-course layer that must be applied prior to the application of Heritage Vintage shingles.

TAMKO® SHINGLE STARTER
A precut universal starter course shingle designed to eliminate the wasted time and material of field cutting 3-tab or roll roofing materials into starter course shingles.

TAMKO® PERFORATED STARTER
Perforated to allow them to be separated into two starter strips. Made of fiberglass mat coated with asphalt and surfaced with ceramic granules.

TAMKO® 10 INCH STARTER
A precut universal starter course shingle designed to eliminate the wasted time and material of field cutting 3-tab or roll roofing materials into starter course shingles. Comes with a factory-applied sealant to eliminate the need for plastic cement. A starter course shingle to get the job started.

Hip & Ridge

HERITAGE® VINTAGE® 12X12 HIP & RIDGE
Forms a cap along various angles of a Heritage® Vintage® roof. Made from a fiberglass mat coated on both sides with weathering-grade asphalt and surfaced with granules.

HERITAGE® DESIGNER RIDGE
Add the perfect finishing touch and create a distinct look in the neighborhood with higher profile Heritage® Designer Ridge shingles.

12-1/4″ X 12″ HIP & RIDGE
Provides a finishing touch for roofs. Precut shingles for installation on hips and ridges. Made with the same fiberglass mat and mineral-granule color blends as Heritage® Series shingles to give the same beautiful wood-shake look on every inch of the roof.

12-1/4″ X 12″ HERITAGE® HIP & RIDGE IR
Provides the finishing touch along with TAMKO’s Heritage IR shingles for complete roof protection. Classified by UL for compliance with UL 2218 Class 4 Impact Resistance.

Ventilation

XTRACTOR VENT® XLP TURBO
Designed to ventilate attic space when used in conjunction with soffit vents. Comes in a roll and can be applied with a nail gun to help speed installation. Exterior baffle design helps guard against wind-driven rain and snow.

COOLRIDGE® VENT
A self-contained 4-foot sectional shingle-over ridge vent designed for ventilation. Features both an external and an internal “sinewave” shaped baffle designed to help guard against wind-driven rain and slow infiltration. Each section also contains integrated end plugs located every foot to reduce scrap when splicing.

RAPID RIDGE® VENT
A self-contained ridge-vent product on a roll that can be installed with a nail gun. Made with a two-layer composite consisting of a nylon-polyester, nonwoven, non-wicking fabric. Heat-bonded to a compression-resistant open-nylon matting of three-dimensional construction. Requires no baffles, metal connectors, end caps or special filters. Capped with roofing shingles and completely hidden.

ROLL VENT® RIDGE VENT
Manufactured using a two-layer composite consisting of a nylon-polyester, non-woven, non-wicking fabric. Heat-bonded to a compression-resistant, open-nylon matting of three-dimensional construction.

QUICKVENT™
A continuous ridge vent designed to ventilate attic space when used in conjunction with soffit vents. Can be installed with a nail gun.

Low-Slope/Flat Roofs

SA BASE AND CAP
Cap: A lightweight, flexible, dual-coated, SBS-modified cap sheet constructed with a nonwoven polyester mat, self-adhering adhesive and a split removable release film on the adhesive side. It is surfaced with ceramic granules to help protect from ultraviolet degradation.

Base: A flexible, fiberglass-reinforced, self-adhering rubberized asphalt sheet membrane with a polymer film on the surface and a removable treated split release film on the adhesive side.

FIBERGLASS SLATE SURFACE ROLL ROOFING
A choice for low-sloped residential roofs. Applied using TAMKO® Cold-Method and Lap Cement or TAMKO Plastic Roof Cement. Available in a variety of colors to complement existing shingles and building materials. Used as the primary roof covering for low-slope residential applications with minimum slopes of 2″ or 12″.

SLATE SURFACED ROLL ROOFING
A choice for low-sloped residential roofs. Applied using TAMKO® Cold-Method and Lap Cement or TAMKO Plastic Roof Cement. Available in a variety of colors to complement existing shingles and building materials. Used as the primary roof covering for low-sloped residential applications with minimum slopes of 2″ on 12″ or as flashing material.